24Vdc-96Vdc to 12Vdc 240w 360w 480w DC Voltage Reducer
Replace diode rectification with synchronous, over88% efficient as high power density
Available for maximum pulse power exceeds 120% of the nominal rating
Wide voltage input , suitable for battery applications ( cell voltage of 1.65V ~ 2.50V)
Smaller, lighter and significantly more quiet than conventional converters
Short circuit / overload output protection (resume after the short circuit disappear)
Applicable to a variety of environmental , protection class IP54
Main technical data
| Model | NQZB200-096-024I | NQZB300-096-024I | NQZB400-096-024I | |
|---|---|---|---|---|
| Input voltage | 24V/36V/48V/60V/72V/84V/96V, 24V to 96VDC | |||
| Input voltage range | DC 20V~100V | |||
| Output voltage | DC 12V | |||
| Output voltage accuracy | 5% | |||
| Output current | 0~10A | 0~15A | 0~20A | |
| Output power | 240W | 360W | 480W | |
| Key switch line starting current | 20~30mA ＜9A@200ms | |||
| Conversion efficiency(full load) | ≥88% | |||
| Static loss after low voltage protection | ≤3mA (0.072W) | |||
| Protection circuit | Overcurrent protection，short circuit protection，self recovery | |||
| Insulation performance [circuit and ground (shell)] | ≥500Ω/V @The AT is(23±2)℃ @The RH is80%～90% | |||
| Insulation [direct dielectric strength of terminals to ground (shell) or circuits not electrically connected to each other] | ≥2000V（DC）（Or rated voltage+1500V）@1min | |||
| Reliability | ≥50000h @Fault free working time | |||
| Durability | ≥10000h @105℃ | |||
| Operating ambient temperature | -20~45℃ | |||
| Relative humidity of working environment | 5%～95%（No condensation） | |||
| Waterproof grade | IP54 | |||
| Mounting hole size | 5mm*6mm*6个 | |||
| Maximum overall dimension | 205mm*92mm*46mm | 205mm*92mm*46mm | 225mm*92mm*46mm | |
| L length in dimension drawing | 180mm | 180mm | 200mm | |
Wiring mode
The output terminals of 120W/240W/360W
The output terminals of 480W
Installation size
See the length of L in the last row of the above technical date table for the corresponding size and length of each model
Precautions
Installation & safety instructions
- The converter must be mounted on solid metal, aluminum for heat dissipation. The converter will be very hot during use, keep wiring from touching the converter and or do not touch it !
- Confirm battery pack main positive and negetive potentials !
- For older cars using a negative through key switch you must use a relay for converter activation. Consult technical services for this application. For radio memory you must either leave the key switch in the on position or hardwire the yellow and red wire to 36/48/60/72 volt positive. Doing this you will have a constant drain on the battery pack and long extended period of “setting” will help drain the battery pack. It is advised for long storage to disconnect the converter.
- Anytime a battery pack is disconnected manufacturers instructions must be followed. Always make sure if the car has a run/tow switch the switch is placed in the tow position before disconnecting anything. Torque battery cable nuts to 80 to 100 inch pounds. Spray coat connections with anti corrosion spray. Tech Note: loose connection create heat and arcing make sure all wiring connections are clean and tight.
- Make sure all wiring is free from moving parts, sharp objects or extreme hot area’s! Tie up any loose wiring
- use process equipment will pay attention to timely remove surface dust and other debris impact of heat dissipations .
- Please don’t disassemble the DC-DC converter yourself . it may cause electric shock or other injuries .
- In order to avoid damaging the power cord , don’t put any object on the line and place the line where it will not be stepped on . If the cord is frayed or damaged , replace it immediately
Warranty: 12 months Limited Warranty from time of delivery
